Toyota Tundra 2000–2026

A badly molded tail lamp socket may not hold the bulb, so brake or tail lamps can fail. The sockets are replaced.³⁶

The exhaust can touch and damage a rear brake line. The exhaust and line are checked and replaced.^37,38

Scratched front lower ball joints can wear, loosen and separate, risking loss of steering. They are replaced.^39,40,37

A passenger airbag switch was fitted without child seat anchors, against the federal standard. The switch is removed.^40,37,38

The airbag status light lens was built wrongly. It is fixed.³⁸

Front lower ball joints can wear early and, in extreme cases, separate. They are replaced.^37,38,41

A wrongly heat-treated slip yoke can break and drop the rear propeller shaft. The shaft is replaced if needed.⁴²

The load capacity labels required by the federal standard are missing. A new label is sent.^{41,42,43,44,45}

A loose or wrong floor mat can trap the accelerator pedal. The pedal is modified and new mats fitted.^42,43,44,45

Rust in the rear crossmember can drop the spare tire and damage the rear brake lines. Parts are replaced or treated.^{1,36,46,39,40}

The accelerator pedal can stick part-way down or return slowly. A reinforcement bar is fitted.^42,43,44,45

A bad weld can let the propeller shaft separate. It is fixed.⁴⁵

Tire pressure warnings were not recalibrated and may not light. They are recalibrated and a new label fitted.^43,44,45,47

A propeller shaft slip yoke can break. It is fixed.⁴⁷

The power window master switch can overheat and melt, a fire risk. It is greased or replaced.^42,43

Misfitted trim can stop an airbag deploying properly. It is fixed.⁴⁸

The passenger front airbag inflator can rupture in a crash. The airbag is replaced.^40,37,38,41

The passenger front airbag inflator can build too much pressure and rupture. The airbag is replaced.^40,37,38,41

The power window master switch can overheat and melt, a fire risk. It is greased or replaced.^44,45,47

The airbag control module was programmed wrongly, so the side curtain airbags may go off unexpectedly. The module is replaced.^38,41

Resin bumper brackets can be damaged. Steel brackets are fitted.^49,50

The passenger knee airbag was fitted with the wrong bolts, which can loosen. The bolts are replaced.⁴⁹

The load labels are wrong. They are replaced.^50,51

Rear seat brackets may be loose. They are fixed.⁵⁰

Electrical interference can switch off stability control. It is fixed.⁵¹

The airbag control unit can wrongly detect faults and turn airbags off. The software is updated.^51,52

The load label overstates the weight of added parts the truck can carry. The label is replaced.^51,52

The passenger airbag inflator can explode. The inflator or airbag is replaced.^40,37,38

The load label may show the wrong capacity. The label is replaced.⁵²

A replacement passenger airbag inflator can explode. The inflator or airbag is replaced.^40,37,38,41

The fuel pump can fail and stall the engine. The pump is replaced.^51,52

The front turn signals are not bright enough to meet the federal standard. They are fixed.^51,52,53

The fuel pump can fail and stall the engine. The pump is replaced.^52,53

Headlight wiring connectors can overheat, a fire risk. The wiring is repaired.^51,52,53,54

The power steering gear may have been built wrongly and leak, losing assist. The gear is checked and replaced as needed.^{55,42,43,44,45,47,56,57,48,58,49,50,51,52,53,54}

In the cold, the parking assist software can block the rear camera image. The software is updated.⁵⁹

Rear axle flange nuts can loosen and let an axle shaft come out. The nuts are tightened and damaged parts replaced.^59,60

The screen can show the front camera instead of the rear in reverse. The software is updated.^59,60

The brake control unit can stop the electric parking brake setting. The software is updated.⁵⁹

A software fault can blank the instrument display. The software is updated.^59,61,60,62

The tonneau cover's joints can loosen and the cover come off. New hardware is fitted.^59,61,60,62

A badly welded spare tire chain can let the spare drop. The carrier is replaced.^61,62

A fuel tube can rub on the brake lines and leak, a fire risk. Protection and a clamp are fitted.^59,61,60,62

The load label is wrong for trucks with a bed liner. The label is replaced.^61,62

The truck can roll in neutral without the brakes on. The transmission software is updated.^{59,61,63,60,62,64}

Machining debris can make the engine's main bearings fail, stalling the engine. The engine is replaced.^3,59,61

Passenger-side tires may have inner sidewall damage and lose pressure suddenly. The tires are checked and replaced as needed.^63,64

Water can get into the reverse lights and make them fail. Both lights are replaced.^{59,61,63,65,60,62,64,66}

A software fault can stop the rearview image showing in reverse. The software is updated.^{59,61,63,65,60,62,64,66}

Machining debris can make the engine's main bearings fail, stalling the engine. The first main bearing is checked and the engine replaced if needed. It widens 24V381000.^4,59,61,63

The camera view may not show when reversing. The parking assist software is updated.^63,65,64,66

The load label may show wrong figures for the weight of added parts. The label is replaced.^{63,65,64,66,67}

Machining debris can make the engine's main bearings fail, stalling the engine. Owners were told a remedy is coming.⁶³

The load label may show wrong figures for the weight of added parts. The label is replaced.^65,66